View SN54AHC16374-08_9100054.PDF datasheet online --- IC-ON-LINE

Datasheet File OCR Text:

sn54ahc16374, sn74ahc16374 16-bit edge-triggered d-type flip-flops with 3-state outputs scls330g march 1996 revised january 2000 1 post office box 655303 ? dallas, texas 75265 members of the texas instruments widebus ? family epic ? (enhanced-performance implanted cmos) process operating range 2-v to 5.5-v v cc 3-state outputs drive bus lines directly distributed v cc and gnd pins minimize high-speed switching noise flow-through architecture optimizes pcb layout latch-up performance exceeds 250 ma per jesd 17 esd protection exceeds 2000 v per mil-std-883, method 3015; exceeds 200 v using machine model (c = 200 pf, r = 0) package options include plastic shrink small-outline (dl), thin shrink small-outline (dgg), and thin very small-outline (dgv) packages and 380-mil fine-pitch ceramic flat (wd) package using 25-mil center-to-center spacings description the 'ahc16374 devices are 16-bit edge-triggered d-type flip-flops with 3-state outputs designed specifically for driving highly capacitive or relatively low-impedance loads. they are particularly suitable for implementing buffer registers, i/o ports, bidirectional bus drivers, and working registers. these devices can be used as two 8-bit flip-flops or one 16-bit flip-flop. on the positive transition of the clock (clk) input, the q outputs of the flip-flop take on the logic levels at the data (d) inputs. a buffered output-enable (oe ) input can be used to place the eight outputs in either a normal logic state (high or low logic levels) or the high-impedance state. in the high-impedance state, the outputs neither load nor drive the bus lines significantly. the high-impedance state and the increased drive provide the capability to drive bus lines without need for interface or pullup components. to ensure the high-impedance state during power up or power down, oe should be tied to v cc through a pullup resistor; the minimum value of the resistor is determined by the current-sinking capability of the driver. oe does not affect internal operations of the flip-flop. old data can be retained or new data can be entered while the outputs are in the high-impedance state. the sn54ahc16374 is characterized for operation over the full military temperature range of 55 c to 125 c. the sn74ahc16374 is characterized for operation from 40 c to 85 c. copyright ? 2000, texas instruments incorporated unless otherwise noted this document contains production data information current as of publication date. products conform to specifications per the terms of texas instruments standard warranty. production processing does not necessarily include testing of all parameters. please be aware that an important notice concerning availability, standard warranty, and use in critical applications of texas instruments semiconductor products and disclaimers thereto appears at the end of this data sheet. epic and widebus are trademarks of texas instruments incorporated. sn54ahc16374 . . . wd package sn74ahc16374 . . . dgg, dgv, or dl package (top view) 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 48 47 46 45 44 43 42 41 40 39 38 37 36 35 34 33 32 31 30 29 28 27 26 25 1oe 1q1 1q2 gnd 1q3 1q4 v cc 1q5 1q6 gnd 1q7 1q8 2q1 2q2 gnd 2q3 2q4 v cc 2q5 2q6 gnd 2q7 2q8 2oe 1clk 1d1 1d2 gnd 1d3 1d4 v cc 1d5 1d6 gnd 1d7 1d8 2d1 2d2 gnd 2d3 2d4 v cc 2d5 2d6 gnd 2d7 2d8 2clk
sn54ahc16374, sn74ahc16374 16-bit edge-triggered d-type flip-flops with 3-state outputs scls330g march 1996 revised january 2000 2 post office box 655303 ? dallas, texas 75265 function table (each 8-bit flip-flop) inputs output oe clk d q l h h l ll l h or l x q 0 h x x z logic symbol 2 2 this symbol is in accordance with ansi/ieee std 91-1984 and iec publication 617-12. 1oe 2oe 1en 1 48 1clk 1d 47 1d1 46 1d2 44 1d3 43 1d4 1q1 2 1q2 3 1q3 5 1q4 6 41 1d5 40 1d6 38 1d7 37 1d8 1q5 8 1q6 9 1q7 11 1q8 12 2d 36 2d1 35 2d2 33 2d3 32 2d4 2q1 13 2q2 14 2q3 16 2q4 17 30 2d5 29 2d6 27 2d7 26 2d8 2q5 19 2q6 20 2q7 22 2q8 23 2en 24 25 2clk c1 c2 1 2 logic diagram (positive logic) 1oe 1clk 1d1 to seven other channels 1q1 2oe 2clk 2d1 2q1 to seven other channels 1 48 47 24 25 36 c1 1d 13 2 c1 1d
sn54ahc16374, sn74ahc16374 16-bit edge-triggered d-type flip-flops with 3-state outputs scls330g march 1996 revised january 2000 3 post office box 655303 ? dallas, texas 75265 absolute maximum ratings over operating free-air temperature range (unless otherwise noted) 2 supply voltage range, v cc 0.5 v to 7 v . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . input voltage range, v i (see note 1) 0.5 v to 7 v . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . output voltage range, v o (see note 1) 0.5 v to v cc + 0.5 v . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . input clamp current, i ik (v i < 0) 20 ma . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . output clamp current, i ok (v o < 0 or v o > v cc ) 20 ma . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . continuous output current, i o (v o = 0 to v cc ) 25 ma . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . continuous current through each v cc or gnd 75 ma . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . package thermal impedance, q ja (see note 2): dgg package 70 c/w . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . dgv package 58 c/w . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . dl package 63 c/w . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . storage temperature range, t stg 65 c to 150 c . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 stresses beyond those listed under aabsolute maximum ratingso may cause permanent damage to the device. these are stress rating s only, and functional operation of the device at these or any other conditions beyond those indicated under arecommended operating conditi onso is not implied. exposure to absolute-maximum-rated conditions for extended periods may affect device reliability. notes: 1. the input and output voltage ratings may be exceeded if the input and output current ratings are observed. 2. the package thermal impedance is calculated in accordance with jesd 51. recommended operating conditions (see note 3) sn54ahc16374 sn74ahc16374 unit min max min max unit v cc supply voltage 2 5.5 2 5.5 v v cc = 2 v 1.5 1.5 v ih high-level input voltage v cc = 3 v 2.1 2.1 v v cc = 5.5 v 3.85 3.85 v cc = 2 v 0.5 0.5 v il low-level input voltage v cc = 3 v 0.9 0.9 v v cc = 5.5 v 1.65 1.65 v i input voltage 0 5.5 0 5.5 v v o output voltage 0 v cc 0 v cc v v cc = 2 v 50 50 a i oh high-level output current v cc = 3.3 v 0.3 v 4 4 ma v cc = 5 v 0.5 v 8 8 ma v cc = 2 v 50 50 a i ol low-level output current v cc = 3.3 v 0.3 v 4 4 ma v cc = 5 v 0.5 v 8 8 ma d t/ d v in p ut transition rise or fall rate v cc = 3.3 v 0.3 v 100 100 ns/v d t/ d v inp u t transition rise or fall rate v cc = 5 v 0.5 v 20 20 ns/v t a operating free-air temperature 55 125 40 85 c note 3: all unused inputs of the device must be held at v cc or gnd to ensure proper device operation. refer to the ti application report, implications of slow or floating cmos inputs , literature number scba004. product preview information concerns products in the formative or design phase of development. characteristic data and other specifications are design goals. texas instruments reserves the right to change or discontinue these products without notice.
sn54ahc16374, sn74ahc16374 16-bit edge-triggered d-type flip-flops with 3-state outputs scls330g march 1996 revised january 2000 4 post office box 655303 ? dallas, texas 75265 electrical characteristics over recommended operating free-air temperature range (unless otherwise noted) parameter test conditions v cc t a = 25 c sn54ahc16374 sn74ahc16374 unit parameter test conditions v cc min typ max min max min max unit 2 v 1.9 2 1.9 1.9 i oh = 50 a 3 v 2.9 3 2.9 2.9 v oh 4.5 v 4.4 4.5 4.4 4.4 v i oh = 4 ma 3 v 2.58 2.48 2.48 i oh = 8 ma 4.5 v 3.94 3.8 3.8 2 v 0.1 0.1 0.1 i ol = 50 a 3 v 0.1 0.1 0.1 v ol 4.5 v 0.1 0.1 0.1 v i ol = 4 ma 3 v 0.36 0.5 0.44 i ol = 8 ma 4.5 v 0.36 0.5 0.44 i i v i = v cc or gnd 0 v to 5.5 v 0.1 1* 1 a i oz v o = v cc or gnd 5.5 v 0.25 2.5 2.5 a i cc v i = v cc or gnd, i o = 0 5.5 v 4 40 40 a c i v i = v cc or gnd 5 v 2.5 10 10 pf c o v o = v cc or gnd 5 v 3.5 pf * on products compliant to mil-prf-38535, this parameter is not production tested at v cc = 0 v. timing requirements over recommended operating free-air temperature range, v cc = 3.3 v 0.3 v (unless otherwise noted) (see figure 1) t a = 25 c sn54ahc16374 sn74ahc16374 unit min max min max min max unit t w pulse duration, clk high or low 5 5.5 5.5 ns t su setup time, data before clk 4.5 4 4 ns t h hold time, data after clk 2 2 2 ns timing requirements over recommended operating free-air temperature range, v cc = 5 v 0.5 v (unless otherwise noted) (see figure 1) t a = 25 c sn54ahc16374 sn74ahc16374 unit min max min max min max unit t w pulse duration, clk high or low 5 5 5 ns t su setup time, data before clk 3 3 3 ns t h hold time, data after clk 2 2 2 ns product preview information concerns products in the formative or design phase of development. characteristic data and other specifications are design goals. texas instruments reserves the right to change or discontinue these products without notice.
sn54ahc16374, sn74ahc16374 16-bit edge-triggered d-type flip-flops with 3-state outputs scls330g march 1996 revised january 2000 5 post office box 655303 ? dallas, texas 75265 switching characteristics over recommended operating free-air temperature range, v cc = 3.3 v 0.3 v (unless otherwise noted) (see figure 1) parameter from to load t a = 25 c sn54ahc16374 sn74ahc16374 unit parameter (input) (output) capacitance min typ max min max min max unit f c l = 15 pf 80* 130* 70* 70 mhz f max c l = 50 pf 55 85 50 50 mh z t plh clk q c l =15 p f 9* 15* 1* 17* 1 17 ns t phl clk q c l = 15 pf 9* 15* 1* 17* 1 17 ns t pzh oe q c l =15 p f 8* 13* 1* 15* 1 15 ns t pzl oe q c l = 15 pf 8* 13* 1* 15* 1 15 ns t phz oe q c l =15 p f 9* 14* 1* 16* 1 16 ns t plz oe q c l = 15 pf 10* 14* 1* 16* 1 16 ns t plh clk q c l =50 p f 10.6 16.2 1 18.5 1 18.5 ns t phl clk q c l = 50 pf 10.6 16.2 1 18.5 1 18.5 ns t pzh oe q c l =50 p f 9.6 14.9 1 16 1 16 ns t pzl oe q c l = 50 pf 9.6 14.9 1 16 1 16 ns t phz oe q c l =50 p f 10.2 15.5 1 17 1 17 ns t plz oe q c l = 50 pf 11.8 15.5 1 17 1 17 ns t sk(o) c l = 50 pf 1.5 ** 1.5 ns * on products compliant to mil-prf-38535, this parameter is not production tested. ** on products compliant to mil-prf-38535, this parameter does not apply. switching characteristics over recommended operating free-air temperature range, v cc = 5 v 0.5 v (unless otherwise noted) (see figure 1) parameter from to load t a = 25 c sn54ahc16374 sn74ahc16374 unit parameter (input) (output) capacitance min typ max min max min max unit f c l = 15 pf 130* 185* 110* 110 mhz f max c l = 50 pf 85 120 75 75 mh z t plh clk q c l =15 p f 5.4* 9.1* 1* 10.1* 1 10.1 ns t phl clk q c l = 15 pf 5.4* 9.1* 1* 10.1* 1 10.1 ns t pzh oe q c l =15 p f 5.1* 9.1* 1* 10.1* 1 10.1 ns t pzl oe q c l = 15 pf 5.1* 9.1* 1* 10.1* 1 10.1 ns t phz oe q c l =15 p f 5* 9.5* 1* 10.5* 1 10.5 ns t plz oe q c l = 15 pf 5* 9.5* 1* 10.5* 1 10.5 ns t plh clk q c l =50 p f 6.9 10.1 1 11.5 1 11.5 ns t phl clk q c l = 50 pf 6.9 10.1 1 11.5 1 11.5 ns t pzh oe q c l =50 p f 6.6 10.1 1 11.5 1 11.5 ns t pzl oe q c l = 50 pf 6.6 10.1 1 11.5 1 11.5 ns t phz oe q c l =50 p f 6.1 10.5 1 11.5 1 11.5 ns t plz oe q c l = 50 pf 6.1 10.5 1 11.5 1 11.5 ns t sk(o) c l = 50 pf 1 ** 1 ns * on products compliant to mil-prf-38535, this parameter is not production tested. ** on products compliant to mil-prf-38535, this parameter does not apply. product preview information concerns products in the formative or design phase of development. characteristic data and other specifications are design goals. texas instruments reserves the right to change or discontinue these products without notice.
sn54ahc16374, sn74ahc16374 16-bit edge-triggered d-type flip-flops with 3-state outputs scls330g march 1996 revised january 2000 6 post office box 655303 ? dallas, texas 75265 noise characteristics, v cc = 5 v, c l = 50 pf, t a = 25 c (see note 4) parameter sn74ahc16374 unit parameter min typ max unit v ol(p) quiet output, maximum dynamic v ol 0.36 0.8 v v ol(v) quiet output, minimum dynamic v ol 0.16 0.8 v v oh(v) quiet output, minimum dynamic v oh 4.6 v v ih(d) high-level dynamic input voltage 3.5 v v il(d) low-level dynamic input voltage 1.5 v note 4: characteristics are for surface-mount packages only. operating characteristics, v cc = 5 v, t a = 25 c parameter test conditions typ unit c pd power dissipation capacitance no load, f = 1 mhz 32 pf
sn54ahc16374, sn74ahc16374 16-bit edge-triggered d-type flip-flops with 3-state outputs scls330g march 1996 revised january 2000 7 post office box 655303 ? dallas, texas 75265 parameter measurement information 50% v cc v cc v cc 0 v 0 v t h t su voltage waveforms setup and hold times data input t plh t phl t phl t plh v oh v oh v ol v ol v cc 0 v 50% v cc 50% v cc input out-of-phase output in-phase output timing input 50% v cc voltage waveforms propagation delay times inverting and noninverting outputs output control output waveform 1 s1 at v cc (see note b) output waveform 2 s1 at gnd (see note b) v ol v oh t pzl t pzh t plz t phz v cc 0 v 50% v cc v ol + 0.3 v 50% v cc 0 v v cc voltage waveforms enable and disable times low- and high-level enabling t plh /t phl t plz /t pzl t phz /t pzh open drain open v cc gnd v cc test s1 v cc 0 v 50% v cc t w voltage waveforms pulse duration input notes: a. c l includes probe and jig capacitance. b. waveform 1 is for an output with internal conditions such that the output is low except when disabled by the output control. waveform 2 is for an output with internal conditions such that the output is high except when disabled by the output control. c. all input pulses are supplied by generators having the following characteristics: prr 1 mhz, z o = 50 w , t r 3 ns, t f 3 ns. d. the outputs are measured one at a time with one input transition per measurement. from output under test c l (see note a) load circuit for 3-state and open-drain outputs s1 v cc r l = 1 k w gnd from output under test c l (see note a) test point load circuit for totem-pole outputs open 50% v cc 50% v cc 50% v cc 50% v cc 50% v cc 50% v cc 50% v cc 50% v cc v oh 0.3 v figure 1. load circuit and voltage waveforms
packaging information orderable device status (1) package type package drawing pins package qty eco plan (2) lead/ball finish msl peak temp (3) 74ahc16374dggre4 active tssop dgg 48 2000 green (rohs & no sb/br) cu nipdau level-1-260c-unlim 74ahc16374dggrg4 active tssop dgg 48 2000 green (rohs & no sb/br) cu nipdau level-1-260c-unlim 74ahc16374dgvre4 active tvsop dgv 48 2000 green (rohs & no sb/br) cu nipdau level-1-260c-unlim 74ahc16374dgvrg4 active tvsop dgv 48 2000 green (rohs & no sb/br) cu nipdau level-1-260c-unlim sn74ahc16374dggr active tssop dgg 48 2000 green (rohs & no sb/br) cu nipdau level-1-260c-unlim sn74ahc16374dgvr active tvsop dgv 48 2000 green (rohs & no sb/br) cu nipdau level-1-260c-unlim sn74ahc16374dl active ssop dl 48 25 green (rohs & no sb/br) cu nipdau level-1-260c-unlim sn74ahc16374dlg4 active ssop dl 48 25 green (rohs & no sb/br) cu nipdau level-1-260c-unlim sn74ahc16374dlr active ssop dl 48 1000 green (rohs & no sb/br) cu nipdau level-1-260c-unlim sn74ahc16374dlrg4 active ssop dl 48 1000 green (rohs & no sb/br) cu nipdau level-1-260c-unlim (1) the marketing status values are defined as follows: active: product device recommended for new designs. lifebuy: ti has announced that the device will be discontinued, and a lifetime-buy period is in effect. nrnd: not recommended for new designs. device is in production to support existing customers, but ti does not recommend using this part in a new design. preview: device has been announced but is not in production. samples may or may not be available. obsolete: ti has discontinued the production of the device. (2) eco plan - the planned eco-friendly classification: pb-free (rohs), pb-free (rohs exempt), or green (rohs & no sb/br) - please check http://www.ti.com/productcontent for the latest availability information and additional product content details. tbd: the pb-free/green conversion plan has not been defined. pb-free (rohs): ti's terms "lead-free" or "pb-free" mean semiconductor products that are compatible with the current rohs requirements for all 6 substances, including the requirement that lead not exceed 0.1% by weight in homogeneous materials. where designed to be soldered at high temperatures, ti pb-free products are suitable for use in specified lead-free processes. pb-free (rohs exempt): this component has a rohs exemption for either 1) lead-based flip-chip solder bumps used between the die and package, or 2) lead-based die adhesive used between the die and leadframe. the component is otherwise considered pb-free (rohs compatible) as defined above. green (rohs & no sb/br): ti defines "green" to mean pb-free (rohs compatible), and free of bromine (br) and antimony (sb) based flame retardants (br or sb do not exceed 0.1% by weight in homogeneous material) (3) msl, peak temp. -- the moisture sensitivity level rating according to the jedec industry standard classifications, and peak solder temperature. important information and disclaimer: the information provided on this page represents ti's knowledge and belief as of the date that it is provided. ti bases its knowledge and belief on information provided by third parties, and makes no representation or warranty as to the accuracy of such information. efforts are underway to better integrate information from third parties. ti has taken and continues to take reasonable steps to provide representative and accurate information but may not have conducted destructive testing or chemical analysis on incoming materials and chemicals. ti and ti suppliers consider certain information to be proprietary, and thus cas numbers and other limited information may not be available for release. in no event shall ti's liability arising out of such information exceed the total purchase price of the ti part(s) at issue in this document sold by ti to customer on an annual basis. package option addendum www.ti.com 27-sep-2007 addendum-page 1
tape and reel information *all dimensions are nominal device package type package drawing pins spq reel diameter (mm) reel width w1 (mm) a0 (mm) b0 (mm) k0 (mm) p1 (mm) w (mm) pin1 quadrant sn74ahc16374dggr tssop dgg 48 2000 330.0 24.4 8.6 15.8 1.8 12.0 24.0 q1 sn74ahc16374dgvr tvsop dgv 48 2000 330.0 24.4 6.8 10.1 1.6 12.0 24.0 q1 sn74ahc16374dlr ssop dl 48 1000 330.0 32.4 11.35 16.2 3.1 16.0 32.0 q1 package materials information www.ti.com 11-mar-2008 pack materials-page 1
*all dimensions are nominal device package type package drawing pins spq length (mm) width (mm) height (mm) sn74ahc16374dggr tssop dgg 48 2000 346.0 346.0 41.0 sn74ahc16374dgvr tvsop dgv 48 2000 346.0 346.0 41.0 sn74ahc16374dlr ssop dl 48 1000 346.0 346.0 49.0 package materials information www.ti.com 11-mar-2008 pack materials-page 2
mechanical data mtss003d january 1995 revised january 1998 post office box 655303 ? dallas, texas 75265 dgg (r-pdso-g**) plastic small-outline package 4040078 / f 12/97 48 pins shown 0,25 0,15 nom gage plane 6,00 6,20 8,30 7,90 0,75 0,50 seating plane 25 0,27 0,17 24 a 48 1 1,20 max m 0,08 0,10 0,50 0 8 56 14,10 13,90 48 dim a max a min pins ** 12,40 12,60 64 17,10 16,90 0,15 0,05 notes: a. all linear dimensions are in millimeters. b. this drawing is subject to change without notice. c. body dimensions do not include mold protrusion not to exceed 0,15. d. falls within jedec mo-153
mechanical data msso001c ? january 1995 ? revised december 2001 post office box 655303 ? dallas, texas 75265 dl (r-pdso-g**) plastic small-outline package 4040048 / e 12/01 48 pins shown 56 0.730 (18,54) 0.720 (18,29) 48 28 0.370 (9,40) (9,65) 0.380 gage plane dim 0.420 (10,67) 0.395 (10,03) a min a max 0.010 (0,25) pins ** 0.630 (16,00) (15,75) 0.620 0.010 (0,25) seating plane 0.020 (0,51) 0.040 (1,02) 25 24 0.008 (0,203) 0.0135 (0,343) 48 1 0.008 (0,20) min a 0.110 (2,79) max 0.299 (7,59) 0.291 (7,39) 0.004 (0,10) m 0.005 (0,13) 0.025 (0,635) 0 ? 8 0.005 (0,13) notes: a. all linear dimensions are in inches (millimeters). b. this drawing is subject to change without notice. c. body dimensions do not include mold flash or protrusion not to exceed 0.006 (0,15). d. falls within jedec mo-118
mechanical data mpds006c february 1996 revised august 2000 post office box 655303 ? dallas, texas 75265 dgv (r-pdso-g**) plastic small-outline 24 pins shown 14 3,70 3,50 4,90 5,10 20 dim pins ** 4073251/e 08/00 1,20 max seating plane 0,05 0,15 0,25 0,50 0,75 0,23 0,13 112 24 13 4,30 4,50 0,16 nom gage plane a 7,90 7,70 38 24 16 4,90 5,10 3,70 3,50 a max a min 6,60 6,20 11,20 11,40 56 9,60 9,80 48 0,08 m 0,07 0,40 0 8 notes: a. all linear dimensions are in millimeters. b. this drawing is subject to change without notice. c. body dimensions do not include mold flash or protrusion, not to exceed 0,15 per side. d. falls within jedec: 24/48 pins mo-153 14/16/20/56 pins mo-194
important notice texas instruments incorporated and its subsidiaries (ti) reserve the right to make corrections, modifications, enhancements, improvements, and other changes to its products and services at any time and to discontinue any product or service without notice. customers should obtain the latest relevant information before placing orders and should verify that such information is current and complete. all products are sold subject to ti?s terms and conditions of sale supplied at the time of order acknowledgment. ti warrants performance of its hardware products to the specifications applicable at the time of sale in accordance with ti?s standard warranty. testing and other quality control techniques are used to the extent ti deems necessary to support this warranty. except where mandated by government requirements, testing of all parameters of each product is not necessarily performed. ti assumes no liability for applications assistance or customer product design. customers are responsible for their products and applications using ti components. to minimize the risks associated with customer products and applications, customers should provide adequate design and operating safeguards. ti does not warrant or represent that any license, either express or implied, is granted under any ti patent right, copyright, mask work right, or other ti intellectual property right relating to any combination, machine, or process in which ti products or services are used. information published by ti regarding third-party products or services does not constitute a license from ti to use such products or services or a warranty or endorsement thereof. use of such information may require a license from a third party under the patents or other intellectual property of the third party, or a license from ti under the patents or other intellectual property of ti. reproduction of ti information in ti data books or data sheets is permissible only if reproduction is without alteration and is accompanied by all associated warranties, conditions, limitations, and notices. reproduction of this information with alteration is an unfair and deceptive business practice. ti is not responsible or liable for such altered documentation. information of third parties may be subject to additional restrictions. resale of ti products or services with statements different from or beyond the parameters stated by ti for that product or service voids all express and any implied warranties for the associated ti product or service and is an unfair and deceptive business practice. ti is not responsible or liable for any such statements. ti products are not authorized for use in safety-critical applications (such as life support) where a failure of the ti product would reasonably be expected to cause severe personal injury or death, unless officers of the parties have executed an agreement specifically governing such use. buyers represent that they have all necessary expertise in the safety and regulatory ramifications of their applications, and acknowledge and agree that they are solely responsible for all legal, regulatory and safety-related requirements concerning their products and any use of ti products in such safety-critical applications, notwithstanding any applications-related information or support that may be provided by ti. further, buyers must fully indemnify ti and its representatives against any damages arising out of the use of ti products in such safety-critical applications. ti products are neither designed nor intended for use in military/aerospace applications or environments unless the ti products are specifically designated by ti as military-grade or "enhanced plastic." only products designated by ti as military-grade meet military specifications. buyers acknowledge and agree that any such use of ti products which ti has not designated as military-grade is solely at the buyer's risk, and that they are solely responsible for compliance with all legal and regulatory requirements in connection with such use. ti products are neither designed nor intended for use in automotive applications or environments unless the specific ti products are designated by ti as compliant with iso/ts 16949 requirements. buyers acknowledge and agree that, if they use any non-designated products in automotive applications, ti will not be responsible for any failure to meet such requirements. following are urls where you can obtain information on other texas instruments products and application solutions: products applications amplifiers amplifier.ti.com audio www.ti.com/audio data converters dataconverter.ti.com automotive www.ti.com/automotive dsp dsp.ti.com broadband www.ti.com/broadband clocks and timers www.ti.com/clocks digital control www.ti.com/digitalcontrol interface interface.ti.com medical www.ti.com/medical logic logic.ti.com military www.ti.com/military power mgmt power.ti.com optical networking www.ti.com/opticalnetwork microcontrollers microcontroller.ti.com security www.ti.com/security rfid www.ti-rfid.com telephony www.ti.com/telephony rf/if and zigbee? solutions www.ti.com/lprf video & imaging www.ti.com/video wireless www.ti.com/wireless mailing address: texas instruments, post office box 655303, dallas, texas 75265 copyright ? 2008, texas instruments incorporated

▲Up To Search▲

Price & Availability of SN54AHC16374-08

	To Download SN54AHC16374-08 Datasheet File
If you can't view the Datasheet, Please click here to try to view without PDF Reader .